Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Don't ignore the forklift at work. If the operation is not good, there will be serious crashes in mins, and there are many crashes involving forklifts.

Case 1: The forklift cargo blocked the vehicle driver's view, and the person in front might not be discovered, leading to a rolling crash.
Instance 2: In order to preserve the balance of the forklift when raising heavy products, the workers utilized their body weight as the weight, which practically triggered casualties.
Case 3: The size of the forklift freight surpasses the allowable size of the path and hangs on the roadside rack, which nearly creates an mishap.
Instance 4: Forklift is speeding up and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not observe the pedestrian, and the pedestrian did not discover the forklift.
Situation 6: The forklift lifts the workers unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter falls and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift vehicle driver did not wear a safety belt and fell from the automobile when it surrendered and was crushed.
Forklift operation ought to take notice of these issues ：.

Start.
1. Before starting, observe the surroundings, and after validating that there are no challenges that impede the safety and security of driving, honk the horn first and then begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) gauge should be safe prior to starting.
3. When the forklift starts with a tons, the motorist must initially verify that the load is secure and trustworthy.
4. The beginning must be slow-moving and constant.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole ought to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When entering and leaving the job website or while driving, take care that there will be no barriers overhead. When the lots is taking a trip, the fork needs to not be increased expensive, which will affect the stability of the forklift. .
3. After discharging, the fork should be decreased to the normal driving placement prior to driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly trigger the automobile to shed lateral security and topple. .
5. When the forklift is downhill, it is strictly forbidden to turn off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are unique conditions.
6. When the forklift is running, it needs to follow the web traffic rules in the factory and need to keep a certain safety and security distance from the car in front. .
7. When the forklift is running, the load has to remain in the most affordable position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised except when stacking or loading. .
8. The elevation of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading things, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special scenarios, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and consistent. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be kept in mind that the fork tip must not touch various other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not permitted to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of Electric Forklift Truck for Warehouse to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as Stand-on Electric Pallet Stacker the vehicle driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look needs to be examined, and gas, lubricating oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and reliable.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not enabled.
2. It is not permitted to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844